Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Aurora?
Gate repair in Aurora typically runs $150 to $650, with most residential fixes landing between $250 and $400. A simple sensor or remote fix sits at the low end, while motor replacement on a commercial slide gate runs higher. The written estimate you get before work starts sets the final price, so there are no surprises once the tools come out.
That range covers the common failures we see across Aurora: a residential swing gate that won’t open, an operator that trips its breaker, a control board that’s stopped talking to the remotes. Electric gate repair is what we do, and we work on the equipment from nine major brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – so a homeowner with a Mighty Mule and a property manager with a DoorKing entry system get the same specialist attention. If your gate needs a full replacement rather than a fix, we handle installation too, which saves you chasing a second contractor when the diagnosis goes that direction.
Key Takeaways
- Typical Aurora gate repair range: $150 to $650
- Residential fixes usually land at $250 to $400
- Motor and control board work drives most of the cost
- A free on-site estimate sets the final price per job
- We work on your brand – residential and commercial operators alike
Gate Repair Cost Breakdown (2026)
The table below gives you the Aurora ranges for the jobs we’re called out to most. These are estimates for common repairs, not quotes. What your gate actually needs comes down to the brand, the operator, and what our technician finds on-site.
| Repair or Service | Typical Aurora Range | What It Covers |
|---|---|---|
| Remote or receiver repair | $150 – $250 | Reprogramming, receiver swap, signal interference troubleshooting |
| Safety sensor or photo-eye repair | $175 – $325 | Realignment, wiring repair, sensor replacement so the gate reverses correctly |
| Control board diagnosis and repair | $250 – $500 | Board testing, component or full board replacement |
| Gate operator (motor) repair | $300 – $650 | Motor assembly, gear and drive work on residential and light-commercial operators |
| Commercial operator repair | $400 – $900+ | High-cycle operators, loop and access control faults, heavy-duty motor assemblies |
| Wiring and power fault repair | $200 – $450 | Tracing shorts, low-voltage runs, connection and ground fault work |
| Manual slide or swing gate hardware | $150 – $350 | Rollers, hinges, latches, track alignment on manual gates |
| Battery backup or power supply | $175 – $400 | Backup battery replacement, transformer and power supply faults |
What pushes a job toward the top of a range: the brand and model of operator. Parts for a heavy-duty FAAC or BFT commercial arm cost more than a residential Ghost Controls unit, and the labor to service a high-cycle operator is longer because there’s more system to test. Wiring faults are the wildcard – a short in a low-voltage run can be ten minutes to find or two hours. If your gate’s been sitting dead for a while, expect a little more diagnostic time than a gate that failed yesterday.
Repair vs. Replace: Which Costs Less?
For most Aurora gates, repair is the cheaper route and we’ll tell you plainly when it is. If the operator is a few years old and the motor, board, or receiver is the only failed part, fixing that part gets you back up and running for a fraction of a new installation. Replacement starts making financial sense when the operator is failing across multiple systems at once, when a high-cycle commercial unit is running far past its service life, or when the gate itself has structural problems the operator can’t overcome. We quote both paths in the same estimate when it’s genuinely close, so you’re not guessing. Whether you need gate repair or a full replacement, you’re dealing with one specialist from diagnosis to install.
What Affects Gate Repair Pricing in Aurora
Aurora has its own mix of housing and commercial property that shapes what a gate job costs here. The Fox Valley’s winter freeze-thaw cycles work hard on gate hardware – posts shift in the ground, tracks ice up and then warp, and low-voltage wiring in exposed runs gets stressed by expanding and contracting soil. That seasonal wear is one reason we see more hardware and alignment work here than you’d find further south. Pricing also moves with these factors:
- Operator brand and grade. A residential Mighty Mule or Ghost Controls operator is simpler and cheaper to service than a commercial DoorKing or Elite high-cycle unit. Parts availability follows the same line – the brand on your gate tells us a lot about what a repair will cost.
- Residential vs. commercial system. Property managers with an HOA entry gate or a commercial slide gate carry heavier motors, loop detectors, and access control. More components mean more to diagnose, so commercial work sits at the top of the range.
- What actually failed. A remote that needs reprogramming is a quick visit. A control board that’s fried, or a motor that’s seized, is not. The diagnosis is where the price range narrows.
- Wiring and power routing. Local codes and permit requirements for electric gate work vary, so checking with the City of Aurora about what your property needs is worth doing. Exposed wiring runs, buried runs, and long distances from the panel add labor.
- Gate type and weight. A light residential swing gate is faster to service than a heavy slide gate on a track. Heavy panels that can crush or slide gates that come off the track carry a bigger job – and a bigger risk if handled wrong.
- Access and site conditions. A gate tucked between a two-car garage and a fence line takes more maneuvering than an open driveway. Weather at the time of service also plays in – a frozen track in January is more work than the same repair in May.
A Word on Safety
An electric gate is a heavy machine with two real dangers: the operator’s wiring and power on one side, and the weight of the panel on the other. A miswired operator can energize parts you’d touch, and a slide gate that’s off its track can come down or drop its rollers. We recommend a trained technician for anything beyond checking the obvious – the breaker, the remote battery, whether the safety sensors are blocked. Our technicians have up to 9 years of experience on electric and automated gate systems specifically, which is the kind of knowledge you want on a powered gate. If your gate is moving when it shouldn’t, or dead when it should open, call us before you start poking at the control box.
How to Save on Gate Repair
There’s no magic discount on gate service, but there are ways to keep the bill at the lower end of the range:
- Get the free estimate first. We give you a written estimate before any work – it’s free, and it’s the number that sets the final price. Call (866) 361-5021 to schedule an on-site estimate.
- Describe the brand and symptom when you call. If you know it’s a LiftMaster or a Linear, say so. Knowing the brand up front means we can plan the right parts and the right technician, which trims diagnostic time.
- Fix small things before they grow. A sensor that’s out of alignment is a cheap fix. Leave it and the operator works harder, and the motor pays for it. Same with a track that’s slightly off – a quick adjustment beats a motor replacement.
- Keep the track and hardware clear. In Aurora, debris, ice, and snow pushed against the gate put load on the operator every cycle. Clearing the track and the gate’s path is the cheapest maintenance there is.
- Ask about repair vs. replace in the same visit. Because we do both, we can quote the fix and the replacement together, so you can compare real numbers rather than guess.
- Don’t let a dead gate sit. A gate that’s been failed for months often picks up secondary problems – stuck hardware, corrosion, damaged wiring. A prompt diagnosis tends to cost less than a delayed one.
One more: if you’re a landlord or property manager with more than one gate, a single visit to look at the whole property usually costs less than separate trips. We work on residential and commercial systems from all nine brands, so a mixed property isn’t a problem. If you want the full picture of what we handle, see Gate Repair Aurora.
Frequently Asked Questions – Gate Repair Cost in Aurora
How much does gate repair cost in Aurora?
Most gate repairs in Aurora cost between $150 and $650, with the average residential job landing around $250 to $400. The final price depends on the brand of operator, what failed, and whether it’s a residential or commercial system. Call (866) 361-5021 for a free estimate – the written estimate sets the price.
Is it cheaper to repair or replace a gate operator?
Repair is usually cheaper, often by hundreds of dollars, when a single component like the motor, board, or receiver has failed. Replacement makes more financial sense when the operator is failing across multiple systems or a high-cycle commercial unit is past its service life. We quote both when it’s close. Call (866) 361-5021 for a free estimate.
How much does electric gate repair cost compared to manual gate repair?
Electric gate repair typically runs $200 to $650 in Aurora, against $150 to $350 for manual gate hardware. The electric system adds the operator, wiring, control board, safety sensors, and power supply – more parts mean a wider range. Call (866) 361-5021 for a free estimate on your system.
Can you repair my gate’s brand, and does brand affect the price?
Yes. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and brand does affect price – commercial-grade operators like FAAC and DoorKing cost more to service than residential units like Mighty Mule and Ghost Controls. Call (866) 361-5021 and tell us your brand for a free estimate.
Can you come today, and does same-day work cost more?
Same-day service is often possible, and the price is set per job by the written estimate – same-day work doesn’t carry a surcharge. We answer 24/7, and we dispatch Sunday through Friday, 7am to 7pm. Call (866) 361-5021 for a free estimate and the next available visit.
Get a Free Gate Repair Estimate in Aurora
A gate that won’t open is a hassle; a gate with a wiring fault is a safety issue. Either way, the fastest route to a straight answer is a call. Tell us the brand and the symptom, and we’ll schedule an on-site estimate at no cost. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (866) 361-5021 today, and we’ll get your gate back up and running.
Written by the team at Gate Repair Aurora.
Pricing reflects the Aurora market as of 2026. Gate Repair Aurora offers free estimates – call (866) 361-5021.
What Our Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Paul Delaney"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Kevin Anderson"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Danielle Gallagher