Gate Repair in Aurora, IL | Gate Repair Aurora

Gate Repair in Aurora - Fixed Today, No Surprise Invoice

Most gate faults are diagnosed and fixed on the first visit. You get the price before we start, and the gate is left working and safe before we leave.

We answer 24/7

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Trusted Gate Repair for Aurora Homeowners

When a driveway gate stops moving, the whole property feels stuck with it. A gate that won’t open on a cold morning, a motor that hums but doesn’t drive, an arm that snapped after a hard winter – these are the problems we handle every day in Aurora. We’re an electric gate specialist, not a fencing company that dabbles in gate work, and we repair and install systems from LiftMaster, FAAC, BFT, Linear and more. Our technicians have up to 9 years of experience, all of it spent on gates.

Call (866) 361-5021

We work on the brand you already own, diagnose the actual failure instead of guessing, and quote a written price before any work starts. Same-day service is available for many repair calls, and we’re insured and bonded. Call (866) 361-5021. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.

Driveway Gate Repair

Driveway Gate Repair is the work we do most: getting the gate at the entrance to your drive swinging, sliding, and latching the way it did before something gave out. You need it when the gate opens partway and stops, when the motor runs but the gate doesn’t move, when a wheel or track is grinding, or when the remote only works from a few feet away. We test the operator, the wiring, the control board, and the mechanical hardware separately, because the same symptom can come from any of them. Most driveway gate repairs in Aurora run $150 to $450 for the repair itself, with operator or control-board replacements climbing into the $400 to $900 range. The written estimate sets the final figure.

What We Check First

We start with the operator and the power supply, since a surprising share of “dead gate” calls trace back to a tripped breaker, a loose low-voltage connection, or a receiver that lost its pairing. From there we move to the mechanical side: hinges, rollers, and the drive mechanism itself. Separating electrical from mechanical early saves you from paying for parts the gate never needed.

When the Operator Is the Problem

If the board is scorched, the motor smells like it burned, or the unit is cycling without command, the operator is usually the fault. We work on LiftMaster, Linear, and other common residential operators and can often repair a control board rather than replace the whole unit. When it does need replacing, we size the new operator to the gate’s actual weight and cycle count.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Gate Welding

Gate Welding is what a failing gate frame often needs before anything else can be fixed, and it’s a job we take seriously because a gate that is welded badly is a gate that can fall. You need welding when a hinge has torn away from the post, when a frame corner has cracked, when a bar or picket has broken free, or when a strike plate has worked loose. We weld steel and iron frames, repair hinge and post connections, and check the whole frame for stress points that will fail next. A single weld repair in Aurora typically runs $150 to $300; a larger frame repair with multiple welds can reach $300 to $600. We quote the repair in writing before we start, and the written estimate sets the final price.

Hinge and Post Connections

A hinge that has pulled out of a steel post usually means the post metal itself has fatigued, not just the hinge. We cut back to sound metal, weld in reinforcement, and reset the hinge so the gate hangs true again. Skipping that step just moves the failure a few inches up the post.

Frame and Bar Repairs

Cracked corners, snapped bars, and bent top rails are common on older gates that have taken a few winters. We re-square the frame before welding so the gate swings without binding once it is back on the hinge. A gate that isn’t square will keep wearing out its hardware no matter how many times the operator is reset.

Commercial Gate Repair

Commercial Gate Repair covers the higher-cycle, heavier-duty side of what we do: entry gates at warehouses, apartment complexes, storage yards, HOAs, and gated communities. You need it when a high-cycle operator is failing, when the gate stops in the middle of a busy drive-through, or when a safety loop or photo-eye has failed and the gate refuses to close. We service commercial-grade operators from FAAC, DoorKing, and BFT, along with the access control that controls them. Typical commercial gate repairs in Aurora run $250 to $600, with heavier operator and control-board work landing in the $600 to $1,500 range. The written estimate is the final word on price.

Safety Devices and Loop Failures

If the gate won’t close, the cause is often the safety edge, photo-eye, or the loop detector that stops the gate when a vehicle is present. We test each safety device independently, repair or replace the failed one, and confirm the operator and the safety edge are talking to each other. Safety devices are not optional on a commercial gate, and we don’t treat them that way.

High-Cycle Operators and Access Control

Operators that run hundreds of cycles a day wear out bearings, gears, and limit switches on a different schedule than a home gate. We check the cycle count, the operator duty rating, and the access control that keys the gate, since a keypad or card reader that has failed can look like a gate problem when it isn’t. If a repair no longer makes sense, we can quote electric gate repair and replacement on the same visit.

Iron Gate Repair

Iron Gate Repair is what an old iron gate usually needs long before it needs replacing, and it’s the kind of repair we do with an eye on how the gate will hold up over the next ten winters. You need it when the gate is sagging, when a hinge has rusted solid, when the latch drags, when a section is bent, or when the gate has started to bind at the top of its swing. We weld, straighten, and re-hang iron gates, check the post for movement, and address rust before it becomes a structural problem. Most iron gate repairs in Aurora run $150 to $450, with bigger rebuilds in the $400 to $800 range. All of it is quoted before we start, and the written estimate sets the final price.

Sagging and Binding Gates

A gate that drags at the bottom or catches at the top is usually sagging at the hinge or has shifted at the post. We measure the gate’s square, check the post plumb, and reset the hinge side instead of fighting the symptom with more torque on the operator. Left alone, a sagging gate will chew through an operator in a season.

Rust and Structural Repairs

Surface rust is cosmetic; rust that has eaten into a weld or thinned a frame member is structural. We clean and prep the area, weld in new metal where it’s needed, and prime and finish the repair so it doesn’t become the next weak point. We don’t paint over a repair that needs more metal.

Sliding Gate Repair

Sliding Gate Repair is the work we do on track-and-roller gates, the kind that roll sideways instead of swinging, and it’s where the failure is often mechanical rather than electrical. You need it when the gate jumps the track, when the rollers grind or seize, when the gate won’t travel its full distance, when the operator strains to move it, or when the gate has started to lean in the opening. We inspect the track, rollers, guide, stop, and operator, replace worn rollers and hardware, and re-align the travel so the gate rolls freely before we reconnect the motor. Typical sliding gate repairs in Aurora fall between $150 and $500, with track and roller replacements pushing into the $500 to $1,000 range on heavier gates. The written estimate sets the price.

Track and Roller Wear

Rollers wear flat, tracks fill with grit, and the gate starts to fight its own path. We inspect each roller, replace the ones that are seizing, and clean and re-level the track so the gate rolls on the full width of the wheel instead of a single edge. A roller repair is far cheaper than an operator replacement, so this is the first place we look.

When the Gate Jumps the Track

A gate that jumps the track is usually off-plumb at the post, worn at the guide, or out of square in the frame. We check all three, because resetting the gate without fixing the underlying cause just puts it back on the track until the next wind. If the gate has come off the track and is leaning, keep people and vehicles clear of it until it’s checked.

Wrought Iron Gate Repair

Wrought Iron Gate Repair is the detail work on a classic iron gate: a broken picket, a lifted scroll, a hinge that has torn loose, a latch that no longer meets the strike cleanly. You need it when an ornamental gate is cosmetically damaged, when a weld has failed at a decorative joint, or when the gate has begun to sag under its own weight. We weld decorative iron, reset hinge and latch hardware, re-square the gate, and match the finish so the repair doesn’t stand out. Most wrought iron gate repairs in Aurora run $175 to $400, with larger frame and ornament rebuilds reaching $400 to $800. We quote the repair before we touch it, and the written estimate is the final price.

Decorative and Scroll Repairs

Scrolls, rings, and finials are the parts most likely to break in a hard knock or a long winter. We weld them back, straighten bent ornament without cracking it, and check whether the break came from impact or from fatigue at the joint. Matching the repair to the original detail is the difference between a gate that looks repaired and one that looks whole.

Hinge and Latch Adjustments

A wrought iron gate that latches hard or swings out of line is usually suffering at the hinge, not the latch. We check the hinge pins, reset the gate, and adjust the strike so the latch engages cleanly and the gate stops where it should. That one adjustment often saves the operator from extra strain over years.

Metal Gate Repair

Metal Gate Repair covers steel, aluminum, and galvanized gates, including the many security and utility gates we see around Aurora. You need it when a post has leaned, when a hinge has broken, when the frame has bent, or when the gate has started to hang and won’t clear the ground. We inspect the post footing, straighten and weld frames, replace worn hinges and hardware, and confirm the gate swings or slides freely before any operator work begins. Typical metal gate repairs in Aurora run $150 to $450, with heavier straightening and post work in the $400 to $800 range. Every repair is quoted in writing before we start, and the written estimate sets the final price.

Post and Frame Straightening

A gate that has stopped clearing the ground is usually a gate whose post has shifted, not a gate whose frame has shrunk. We check footing depth and post plumb before reaching for a torch, because fixing the frame without fixing the post just delays the same call. When a post has to be reset, we tell you what the gate will need to go back on it correctly.

Hardware and Hinge Replacement

Hinges, latches, and stops are the parts that fail first on a metal gate, and they’re the parts that decide whether the gate hangs true. We replace worn hinges, re-drill latch positions where they’ve worked loose, and check that the gate opens to a solid stop. Small hardware now is much less than an operator later.

Wood Gate Repair

Wood Gate Repair is the wood-specific side of our gate work, and it’s where our local climate matters more than anywhere else. Lake-effect weather around Aurora means freeze-thaw cycles, humid summers, and long wet springs, and wood gates take that abuse at every joint. You need it when boards have warped or split, when the frame has swelled and started to bind, when a hinge has pulled out of wet wood, or when a wood gate has started to sag. We repair frames and boards, reset hinges and hardware, re-brace the frame, and prep the repair for a proper finish. Most wood gate repairs in Aurora land between $150 and $400, with larger frame and board rebuilds in the $400 to $800 range. The written estimate sets the price, and we quote before we start.

Warping and Swelling

A wood gate that binds in July and swings free in January is a gate that has taken on moisture unevenly. We check the frame for swelling, adjust the hardware, and brace or repair boards that have moved permanently. If the gate is going to keep moving with the seasons, we make sure the hardware can take it.

Hinge Pull-Out and Frame Bracing

When a hinge pulls out of wood, it’s usually because the wood behind it has softened. We repair the surrounding board or frame member, add bracing where the hinge needs support, and reset the hinge so the gate hangs on sound material. Treating the repair is what keeps the same hinge from pulling out in the next wet season.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Brands We Service

We service LiftMaster equipment and know where it wears out: the drive gears on older units, the limit switches that lose their setting, and the receiver that stops pairing after a power event. FAAC and BFT operators, which are common on commercial and high-cycle installs, are familiar territory too, including their control boards, safety inputs, and hydraulic or electromechanical drive assemblies. Linear residential openers show up on a lot of Aurora driveways, and we know the board and motor failures that stop them cold.

Below the surface, the pattern is the same across every brand we work on. We work on your brand by understanding how its operator was designed, not by swapping parts until one happens to fit. That familiarity is why we’re comfortable with both a residential Mighty Mule and a commercial DoorKing, and why we don’t need to guess where a fault is likely to live. Whether you have a LiftMaster, a FAAC, a BFT, a Linear, or any other make, we can help, and if the gate needs replacing rather than repairing, we can quote the installation too.

Signs You Need a Pro Right Now

  • The gate stops partway. An operator that reverses or stops mid-travel is usually meeting resistance it wasn’t designed for, from a binding hinge, a failing limit switch, or an obstruction in the path. Stop using the gate until it’s checked, because forcing it can turn a repair into an operator replacement.
  • The motor hums but the gate doesn’t move. This usually means the drive mechanism has slipped, a chain or gear has worn, or the operator has lost its limit. Left alone, a humming motor can burn itself out in a short time.
  • The gate is leaning or has jumped the track. A leaning swing gate or a slide gate off its track is a structural problem, not a remote problem. It can drop without warning, so keep people and vehicles clear and get it looked at.
  • The gate doesn’t close all the way. A gate that stops short of the latch is often a safety-device fault, a misaligned strike, or a limit issue. It is also a security gap, so this is worth a same-day call.
  • The remote only works up close, or not at all. Keypad and receiver failures are common and usually fixable without a full operator swap. We test the receiver, the remote, and the wiring before recommending anything.

Our Process, Step by Step

  1. 1
    Listen to the symptoms. We start by asking what the gate does and doesn’t do, because the pattern of failure often points at the system before we see it. That short conversation narrows the diagnosis before we ever open the operator.
  2. 2
    Inspect on site. We check the operator, wiring, safety devices, and the mechanical hardware separately, so electrical symptoms don’t get blamed on a mechanical part. We look at the gate’s hang and travel, because the frame tells us a lot about how the system has been wearing.
  3. 3
    Diagnose with the right tools. We use a meter to test the power and low-voltage side, test the safety inputs individually, and cycle the operator under load to see where the failure shows up. That is how we separate a failed receiver from a failed board.
  4. 4
    Quote in writing before we start. You get a clear price for the repair, and you approve it before any work begins. If we find a second issue while we’re in there, you hear about it before we add it to the bill.
  5. 5
    Repair, test, and walk you through it. We test the full open, close, and safety cycle after the repair, then show you what we fixed and what to watch for. If the gate needs more than repair, we quote the replacement and the installation on the spot.

If the call is about a new gate rather than a repair, our gate installation service covers the whole job, from sizing the operator to setting the post and wiring the controls.

How Much Does Gate Repair Cost in Aurora?

A typical driveway gate repair in Aurora runs $150 to $450, and a commercial or high-cycle gate repair runs $250 to $600. Those ranges cover the repair itself; an operator or control-board replacement adds on top of them and usually puts the job in the $400 to $900 range for a residential gate and the $600 to $1,500 range for commercial work.

What affects the price is the type of gate, the operator, and how much of the system has failed. A single weld repair is at the low end; a gate whose post has moved, whose hinge has broken, and whose operator has been straining as a result is at the high end. Wood gate repairs move with the frame and board condition, while iron and metal repairs track the amount of welding and finish work. Commercial gates carry higher-cycle operators and safety devices that need testing, and that’s reflected in the range.

How you avoid overpaying is simple: get the price in writing before anyone touches the gate, and ask which parts of the system have been tested. A repair quoted after a clear diagnosis is much more predictable than a quote based on a guess.

What’s included in our free estimate in Aurora is a real on-site look at the gate, a test of the operator and safety devices, and a written price for the repair. The written estimate sets the final figure, and the price you approve before work starts is the price you’ll be asked to pay.

Our Service Area Near Aurora

We work throughout Aurora and the surrounding Fox Valley towns, including North Aurora, Montgomery, Batavia, Oswego, Warrenville, and Sugar Grove. When the call is outside the city, the nearby gate repair we handle in Cortland and the work in Stone Park are typical of what gets scheduled. Response times depend on where you are and how the day is booked, so call and we’ll tell you the soonest opening.

Serving Aurora, IL – Our Local Coverage Area

We serve Aurora and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Gate Repair in Aurora

Schedule Your Gate Repair Service in Aurora Today

If your gate isn’t working the way it should, call us and let’s get it back up and running. We’re an insured, bonded, electric gate specialist serving Aurora and the surrounding towns, and every repair is quoted in writing before work starts, with a free estimate. Call (866) 361-5021. We answer 24/7, and fast dispatch from 7am to 7pm runs Sunday through Friday. If you’re comparing local options, our home page at Gate Repair Aurora is a good place to start, and you can also read more about the gate repair we do across the area.

Written by the team at Gate Repair Aurora.

Why Aurora Chooses Gate Repair Aurora

We set the standard for gate repair in Aurora.

30-60 Min Response

Fast dispatch across Aurora, 7am-7pm. Same-day service available.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Aurora

Getting your gate repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your gate repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

Licensed Technician Dispatched

A background-checked, certified technician arrives in Aurora - typically within 30-60 minutes.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local gate repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    A background-checked tech heads outLicensed & insured, typically within 60 minutes.
  4. 4
    You approve before work beginsNothing starts until you say go.

What Aurora Customers Say

Trusted by homeowners across Aurora and surrounding areas.

★★★★★

"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."

Paul Delaney
★★★★★

"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."

Kevin Anderson
★★★★★

"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."

Danielle Gallagher

Ready for Gate Repair in Aurora?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in Aurora.

(866) 361-5021

Request a Free Estimate in Aurora

Tell us about your gate repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Local Service Coverage
Call Now - We Answer 24/7